Auto verify

IBR Auto-Verify Workflow

IBR's auto-verify workflow automatically captures a baseline before every UI file edit, waits for HMR to apply the change, re-scans, and reports what changed. This runs via Claude Code hooks — no manual commands needed once configured.

What It Does

For every Write|Edit on a UI file (.tsx, .jsx, .vue, .svelte, .css, .scss, .html):

1. Pre-edit — silently captures a baseline scan + screenshot
2. Edit happens — Claude makes the change
3. Post-edit — waits for HMR, re-scans, diffs against baseline, outputs a verdict block

Claude reads the verdict and decides whether the edit achieved the intended result, or if it needs a follow-up fix.

Configuration (Required — Opt In)

Create .ibr/config.json in your project root:

{
  "autoVerify": true,
  "projectRoot": "/absolute/path/to/project",
  "devServerUrl": "http://localhost:3000"
}

All three fields are required for the workflow to fire:

Field	Purpose
autoVerify	Master switch. false (default) = workflow never runs
projectRoot	Absolute path to the project. Hook only fires if $PWD is under this path
devServerUrl	URL the hook scans. Skip port auto-detection — use this URL directly

Default is off — any project without this file or without autoVerify: true has zero overhead and zero hook noise.

Gate Logic (What Prevents Noise)

The pre-change hook has 5 gates. If any fail, the hook exits silently and no scan runs:

1. UI file extension — only .tsx/.jsx/.vue/.svelte/.css/.scss/.html
2. Opt-in flag — .ibr/config.json must exist with autoVerify: true
3. Project boundary — $PWD must be under config.projectRoot (prevents scanning project A while editing project B)
4. Rate limit — 10s minimum between cycles (batches rapid edits)
5. Dev server reachable — config.devServerUrl must respond (or parallel port probe finds one)

Verdict Output

The post-change hook outputs one of three formats to stdout (which Claude reads):

Clean pass (condensed):

IBR: ✓ PASS (+2 elements)

One line. Minimal context cost. Used when scan verdict is PASS and zero issues detected.

Review block (when scan passes but issues exist):

IBR Post-Change Verification
File: src/app/page.tsx
URL:  http://localhost:3000

Before: PASS (42 elements, 0 issues)
After:  PASS (44 elements, 2 issues)
Elements: +2 added

Issues:
  [warning] button.submit contrast ratio 3.2:1 (need 4.5:1)
  [warning] h2.section-title missing aria-level

Verdict: REVIEW — scan passed but 2 issue(s) found.

Needs-fix block (when scan fails):

IBR Post-Change Verification
File: src/app/page.tsx
URL:  http://localhost:3000

Before: PASS (42 elements, 0 issues)
After:  FAIL (40 elements, 3 issues)
Elements: -2 removed

Issues:
  [error] button.submit has no click handler (hasOnClick: false)
  [error] form missing action attribute
  [warning] div.success-message contrast 3.2:1

Console errors:
  Uncaught TypeError: Cannot read property 'onClick' of undefined

Verdict: NEEDS_FIX — address issues above before proceeding.

How to Enable

# 1. Create .ibr directory if needed
mkdir -p .ibr

# 2. Write config file (adjust paths and URL)
cat > .ibr/config.json <<EOF
{
  "autoVerify": true,
  "projectRoot": "$(pwd)",
  "devServerUrl": "http://localhost:3000"
}
EOF

# 3. Start your dev server
npm run dev  # or whatever your project uses

# 4. Make a UI edit — the hooks will fire automatically

How to Disable

Set autoVerify: false in .ibr/config.json, or delete the file entirely.

Troubleshooting

No verdict appears after edit:

• Check .ibr/config.json has autoVerify: true and correct projectRoot
• Check dev server is actually running at devServerUrl
• Check $PWD is under projectRoot (the hook uses absolute path matching)
• Check the edited file has a UI extension

"Post-change scan failed — dev server may be down":

• Dev server crashed during or after the edit
• HMR took longer than the 10s wait — increase MAX_WAIT in hooks/ibr-post-change.sh if needed

Verdict refers to the wrong URL:

• Remove devServerUrl from config to trigger port auto-detection
• Or explicitly set it to the URL you want scanned

Hooks firing on unrelated project:

• The projectRoot gate should prevent this. Verify the config file is in the project you actually want scanned, not a parent directory.

Files Involved

• hooks/ibr-pre-change.sh — PreToolUse hook, captures baseline
• hooks/ibr-post-change.sh — PostToolUse hook, scans and reports verdict
• hooks/hooks.json — registers both hooks
• .ibr/config.json — per-project opt-in config (you create this)
• .ibr/pre-change-state.json — ephemeral state between pre and post hooks (auto-managed)
• .ibr/pre-change-scan.json — baseline scan data (auto-managed)
• .ibr/post-change-scan.json — post-edit scan data (auto-managed)
• .ibr/autoscan-last-run — rate limit timestamp (auto-managed)

Add .ibr/ to .gitignore.