Ila hw debug

ILA Hardware Debug

On-silicon debug methodology. Insert an Integrated Logic Analyzer (ILA), re-run implementation so the debug core is real in the routed netlist, program the board with the matching probes file, arm a trigger, capture, and read back the waveform. This is for behavior you cannot see in simulation: real I/O timing, real PLL lock, real DDR/transceiver/external-device interaction, metastability, and "works in sim, fails on the board" bugs.

The discipline here is the same as timing closure: observe before you change, insert the smallest probe that answers the question, capture FRESH hardware evidence before claiming anything, and never invent a "trigger hit" you did not read back from the device.

When to use

• "Debug on hardware", "insert an ILA", "capture a waveform on the board".
• A design passes simulation but misbehaves on real silicon (I/O, clocking, external memory/peripheral, link training, reset sequencing).
• You need to trigger on a specific live condition (state == ERROR, fifo_full && wr_en, an address range) and see the surrounding cycles.
• You need to read a current live value or drive a control bit at runtime (VIO).
• You need to verify a fix actually took effect in hardware, not just in a report.

When NOT to use

• The bug is reproducible in simulation -> use the simulation skill (sim_compile / sim_run / sim_probe). Sim is faster, fully observable, and free; exhaust it first. ILA only sees what you wired up and only after a full build.
• A timing problem (WNS/TNS negative) -> close timing first. Probing a design that does not meet timing gives you garbage captures; the timing-closure skill comes first.
• You only need static facts about the routed design (utilization, DRC, timing, power) -> those are report tools, no hardware needed.
• You want to change RTL behavior. ILA observes; it does not fix. Use it to localize, then hand the root cause to the RTL/timing/CDC skill.

Prerequisites (verify first)

Do not skip. Most "ILA doesn't work" reports are a broken prerequisite, not a bug.

1. MCP + Vivado link alive: test_connection. If it fails, the Tcl server inside Vivado is not running — stop and tell the user to start it.
2. A project is open with a known top: get_project_info. ILA insertion edits this design.
3. Decide the insertion path (see Decision Table). Confirm which one the design uses before touching anything:
   • Netlist (HDL) flow: mark signals in RTL -> setup_debug on the synthesized netlist. Use list_source_files to confirm the RTL exists.
   • Block Design flow: list_block_designs; instantiate bd_create_ila / bd_create_system_ila and wire probes in the BD.
4. Physical board reachable (for the program/capture half):
   • open_hardware_manager
   • connect_hardware_server (default localhost:3121 — a hw_server process must be running and the board powered + JTAG-connected). If this fails, it is an environment problem: no board, no driver, or hw_server down. Say so — do not fake a capture.
   • list_hardware_targets then open_hardware_target — confirm a target exists.
   • list_hardware_devices — confirm the FPGA is detected on the JTAG chain.
5. A debug-enabled bitstream + its .ltx must exist before you can capture. If the current bitstream has no debug core, you are in Phase A (insert), not Phase C (capture).

If any prerequisite fails, report exactly which one and stop. Do not proceed with a half-connected toolchain.

---

METHODOLOGY

The flow has three phases. Phase A (insert + rebuild) only runs if the design does not already contain the ILA you need. Phase B (program). Phase C (arm, capture, read). If a debug bitstream + .ltx already exist for the exact signals you need, skip straight to Phase B.

Phase A — Insert / connect the ILA (only if not already present)

A1. Pick the smallest probe set that answers the question. State, before inserting, what condition you are hunting and which signals prove or disprove it. ILA costs BRAM and routing; do not blanket-probe a bus you do not need. Width × depth is the budget — capture the suspect control/handshake signals and the few data bits that matter.

A2a. Netlist (HDL) insertion — preferred when probing internal RTL signals:

1. mark_debug_signal for each signal of interest. (Equivalently, the user can add (* MARK_DEBUG = "true" *) in RTL; list_debug_signals confirms what is marked.) These signals must survive synthesis — a signal optimized away cannot be probed; if it is missing after synth, it was merged/trimmed.
2. run_synthesis_async -> poll get_run_status until done -> get_synthesis_report. Use open_synthesized_design so the netlist is in memory.
3. setup_debug — auto-builds the ILA core and connects all MARK_DEBUG signals (one clock domain per ILA core; mixed-domain signals need separate cores or you get an invalid setup).
4. list_debug_cores + list_debug_signals — verify the core exists and the intended signals are actually attached before spending a build.
5. implement_debug_core then write_debug_probes (produces the .ltx that the hardware side needs to name probes). Keep the .ltx next to the bitstream so program_device auto-associates it.

A2b. Block-Design insertion — preferred for AXI / interface / system-level debug:

1. bd_create_system_ila (interface-aware, for AXI/AXIS/handshake interfaces) or bd_create_ila (pin-level) and configure depth with bd_ila_set_probe_width / bd_system_ila_set_slot as needed.
2. bd_connect_system_ila_interface (interface) or bd_connect_ila_probe + bd_connect_ila_clock (pins). The ILA clock MUST be the clock of the domain you are sampling.
3. bd_validate_design — must pass clean before generating. Unconnected probe/clock = invalid capture.
4. bd_generate_output_and_wrapper, then bd_wait_on_output_generation / bd_check_output_status.

A3. Size the ILA deliberately (create_ila if instantiating directly, else the BD config tools). sample_depth ∈ {1024 … 131072}: deeper = more BRAM, more build time. num_probes up to 64. Start modest; widen only if the first capture proves you need more window or more signals.

A4. Re-implement and re-bitstream — the debug core must be real in routed silicon.

• run_implementation_async -> poll get_run_status until complete.
• report_drc — must be clean (debug-core insertion can introduce real DRC issues; do not ignore them).
• Check timing did not regress from the inserted core: report_timing_summary -> extract_timing_metrics. If WNS went negative because of the ILA, that is a real regression — hand to the timing skill; do not paper over it.
• generate_bitstream. Confirm the returned .bit path. write_debug_probes must have produced the matching .ltx.

One change-class per build. Do not simultaneously add probes, retime RTL, and tweak strategy — if the next capture looks wrong you will not know which change caused it.

Phase B — Program the board

1. Re-confirm the live connection: open_hardware_manager, connect_hardware_server, open_hardware_target, list_hardware_devices.
2. program_device with the debug .bit. Leave probes_file empty to auto-detect the .ltx beside the bitstream, or pass it explicitly. The .ltx MUST match this exact bitstream — a stale .ltx gives wrong/garbage probe names and silently meaningless captures.
3. refresh_hardware_device then hw_ila_list — verify the ILA core(s) appear with the expected probe count. No ILA listed = wrong bitstream, missing .ltx, or insertion failed. Stop and fix; do not pretend to capture.

Phase C — Arm, trigger, capture, read

1. hw_ila_get_status — read current core status, depth, and probe names. Use the exact probe names it returns for all trigger calls.
2. Set the trigger (the heart of useful capture):
   • hw_ila_set_trigger(probe, value, operator, radix) per probe. Use radix="bin" with X don't-care bits for bit-field conditions (e.g. "XXXX1XXX"), radix="dec"/"hex" for values, and operator ∈ eq/neq/gt/lt for ranges.
   • Multiple probes: hw_ila_set_trigger_condition("AND" | "OR") to combine.
   • hw_ila_clear_trigger to reset a probe (or all) if you mis-set it.
   • For a free-running snapshot with no condition, skip the trigger and use trigger_now=True in the next step.
3. Confirm the trigger before arming: hw_ila_get_status again and read back the per-probe compare values and AND/OR mode. The condition you intended must be the condition shown. Set trigger_position so you capture enough pre-trigger context (e.g. center the window).
4. Arm: hw_ila_run (or hw_ila_run(trigger_now=True) for immediate). Status should report ARMED (or TRIGGERED if it fired instantly).
5. Provoke the condition. If a runtime stimulus is needed and a VIO exists, hw_vio_list -> hw_vio_get_probes -> hw_vio_write to drive control bits, hw_vio_read to observe live values. Otherwise the DUT/external event drives it.
6. Wait for capture: hw_ila_wait(timeout=N). Final status IDLE = capture complete (trigger hit + buffer full). Still ARMED after timeout = trigger never fired — that is a real result, not an error to hide (see loop).
7. Read back: hw_ila_read_data(file_path="...csv") to upload the samples and save the waveform CSV. Report the sample count and CSV path. This CSV — not any inference — is the evidence.
8. Cleanly disconnect_hardware when the session is done (leaving the target open can block other tools / other users of the board).

---

Decision table — symptom -> likely cause -> safe next action

Symptom (from a tool, not a guess)	Likely cause	Smallest safe action
connect_hardware_server fails	hw_server down / board off / JTAG unplugged	Environment problem — report it; do not fabricate a capture
list_hardware_devices empty	Wrong target, power, or cable	refresh_hardware_device, re-open_hardware_target; if still empty, hardware issue
hw_ila_list empty after programming	Bitstream has no debug core, or .ltx not associated	Re-program with the debug .bit; confirm matching .ltx; if none exists, do Phase A
Probe name from RTL not in hw_ila_get_status	Signal optimized away in synth, or stale .ltx	Re-check list_debug_signals; if trimmed, mark a retained equivalent / add keep; regenerate .ltx with the bitstream
hw_ila_wait stays ARMED (never triggers)	Trigger condition never true, wrong radix, wrong probe, or signal stuck	Re-verify condition via hw_ila_get_status; loosen with don't-cares / trigger_now=True to snapshot; check the signal is even toggling
Capture looks like noise / constant	Wrong clock domain on ILA, or .ltx/.bit mismatch	Confirm ILA clock = sampled domain; re-pair .bit + .ltx; rebuild if domain is wrong
ILA insertion broke timing (WNS<0)	Debug core added load/routing pressure	Reduce depth/probe count; if still negative, hand to timing-closure skill — do not waive
report_drc errors after implement_debug_core	Real DRC from inserted core (clocking, BUFG, etc.)	Fix the DRC; never ignore to force a bitstream
Need to change a control bit live	Static probing insufficient	Add/Use a VIO (bd_create_vio / create_vio), then hw_vio_write

---

Capture loop (iterate until the trigger answers the question)

This is a measure -> adjust trigger -> re-measure loop. The only thing that changes between iterations should be the trigger condition, not the bitstream — re-arming is seconds, re-building is minutes.

1. hw_ila_get_status                  # confirm probes + current condition
2. hw_ila_set_trigger (+ condition)   # one trigger hypothesis at a time
3. hw_ila_get_status                  # VERIFY the condition you intended is set
4. hw_ila_run                         # arm
5. (provoke; hw_vio_write if needed)
6. hw_ila_wait(timeout=N)             # IDLE = captured; ARMED = no trigger
7. hw_ila_read_data(file_path=...)    # save CSV evidence
   -> inspect: did the captured window contain the event?

STOP conditions — halt the loop and report:

• Captured the event: hw_ila_wait returned IDLE and the CSV shows the condition + surrounding cycles. Done — report the CSV.
• Trigger genuinely never fires after loosening (don't-cares / trigger_now) and you have confirmed the probe is toggling: this is a finding — the condition you expected does not occur in hardware. Report it; hand the root cause to the RTL/CDC/timing skill. Do not keep re-arming hoping it changes.
• Window too small / wrong signals: if you need a deeper buffer or more probes than the current core has, you must return to Phase A (rebuild). Do this deliberately, one change-class at a time — note it as a build iteration, not a loop iteration.
• Need an RTL/architectural fix: ILA localized the bug. ILA cannot fix it. Present the captured evidence + the hypothesis and hand off. Do not loop.
• Hardware/connection lost mid-loop: refresh_hardware_device; if the device is gone, stop — it is an environment failure, not something to retry forever.

Each iteration, show the trigger you set and the resulting status (ARMED vs IDLE) so cause and effect are attributable.

---

Safety rails (do not violate)

• Evidence before claims. "Triggered", "captured", "the signal does X on hardware" REQUIRE a fresh hw_ila_wait IDLE result and a real hw_ila_read_data CSV from this programmed device. Never infer a capture from simulation, from a report, or from a prior run. If you did not read it back from silicon, you do not know it.
• .ltx must match the .bit. Programming a debug bitstream with a stale or foreign .ltx yields plausible-looking but meaningless probe names and data. Always regenerate write_debug_probes with the bitstream and verify probe names via hw_ila_get_status.
• No fake-pass on the rebuild. Inserting an ILA can create real DRC violations or break timing (WNS<0). Do NOT waive DRC, set_false_path, or relax timing just to get a debug bitstream out. If the inserted core breaks signoff, that is a real regression — reduce the probe budget or hand to the timing/DRC skill. Any exception requires an explicit stated assumption and, if it could be real, asking the user first.
• Observe, don't silently edit. ILA is a measurement instrument. Do not modify RTL to "make the trigger fire." If the design must change, recommend the edit with the captured evidence; let the human / the RTL skill apply it.
• Smallest probe first. Constraints/marking before re-architecting; a few targeted probes before a wide bus. Don't blow the BRAM/depth budget on a fishing expedition.
• No invented tools. Only the hw_ila_*, hw_vio_*, hw_axi_*, hardware- manager, *_debug*, bd_*ila*, and build tools named here exist. If a needed capability (e.g. cross-trigger, advanced sequencer) is not in the toolset, say so plainly rather than pretending.
• VIO writes drive real hardware. hw_vio_write toggles live control bits on a running board. Only drive probes whose effect you and the user understand; confirm before writing anything that could put external hardware in a bad state.
• Leave the target clean. disconnect_hardware when done so the board/JTAG is not left locked.

---

Output

Report, in order:

1. Insertion summary (if Phase A ran): which path (netlist vs BD), signals probed (from list_debug_signals / hw_ila_get_status), ILA depth × probe count, and the post-implementation evidence that the rebuild is clean — report_drc result + WNS/TNS from extract_timing_metrics. State explicitly whether the ILA changed timing.
2. Program confirmation: bitstream path, .ltx path, and the hw_ila_list output proving the core is live on the device.
3. Trigger setup: the exact per-probe compare values + AND/OR mode, copied from hw_ila_get_status (the verified condition, not the intended one).
4. Capture result: final hw_ila_wait status (IDLE = success), sample count, and the saved CSV path from hw_ila_read_data. If it never triggered, say so and state what that implies.
5. Finding + handoff: what the waveform shows about the original question, and — if a fix is needed — the recommended RTL/timing/CDC action handed to the appropriate skill, with the CSV as evidence. Never close with an unverified "fixed on hardware" claim.